Redirected from Touch tone
Prior to DTMF the phone systems had used a series of clicks on the phone line to dial numbers, a system known as pulse dialing. The clicks were actually the connection of the phone line being made and broken, like flicking a light switch on and off. This was useful only as far as the local end office where the wires stopped, requiring operator intervention for long distance dialing.
DTMF was developed at Bell Labs in order to allow dialing signals to dial long-distance numbers, potentially over non-wire links such as microwave links or satellites. Encoder/decoders were added at the end offices that would convert the standard pulse dialing clicks into DTMF tones and play them down the line to the remote end office. At the remote site another encoder/decoder would decode the tones and turn out a series of clicks. It was as if you were connected directly to that end office, yet the signaling would work over any sort of link. This idea of using the existing network for signaling as well as the message is known as in-band signaling[?].
It was clear even in the late 1950s when DTMF was being developed that the future of switching lay in electronic switches, as opposed to the mechanical crossbar systems currently in use. In this case pulse dialing made no sense at any point in the circuit, and plans were made to roll DTMF out to end users as soon as possible. Various tests of the system occurred throughout the 1960s where DTMF became known as Touch Tone.
The Touch Tone system also introduced a standardized keyboard layout. After testing no less than 18 different layouts, they eventually chose one that remains similar to those in use today, with 1 in the upper-left and 0 at the bottom. The adding-machine layout, with 1 in the lower-left was also tried, but at the time few people had used one and having the 1 at the "start" in normal England reading order led to fewer typing errors. I retrospect this turned out to be a bad idea, with the widespread introduction of computers and bank machines the phone keyboard is now the "oddball" and has led to continued mis-typing today.
The engineers had also envisioned phones being used to access computers, and surveyed a number of companies to see what they would need for this role. This led to the addition of the pound (#) and star (*) keys, as well as a group of keys for menu selection, A, B, C and D. In the end the lettered keys were dropped from most phones, and it was many years before the # and * keys became widely used. Many non-telephone applications still use the alphabet keys, such as Amateur Radio repeater signaling and control.
The US military also used the letters, relabled, in their Autovon phone system. Here they were used before dialing the phone in order to give some calls priority, cutting in over existing calls if need be. The idea was to allow important traffic to get through every time. Pressing C, Immediate, before dialing would make the switch first look for any free lines, and if all lines were in use, it would hang up any non-priority calls, and then any Priority calls. While the Autovon phone system no longer exists, their original names were Flash Override (A), Flash (B), Immediate (C), and Priority (D). Pressing one of these keys gave your call priority, over-riding other conversations on the network. Flash Override is the highest priority.
The DTMF keypad is laid out in a 4 x 4 matrix with each row representing a low frequency, and each column representing a high frequency. Pressing a single key such as '1' will send a sinusoidal tone of the two frequencies 697 and 1209 hertz (Hz). The two tones are the reason for calling it multi-frequency. These tones are then decoded by the switching center in order to determine which key was pressed.
| 1 | 2 | 3 | A | 697 Hz |
|---|---|---|---|---|
| 4 | 5 | 6 | B | 770 Hz |
| 7 | 8 | 9 | C | 852 Hz |
| * | 0 | # | D | 941 Hz |
| 1209 Hz | 1336 Hz | 1477 Hz | 1633 Hz |
The frequencies were initially designed with a ratio of 21/19, which is slightly less than a whole tone, to avoid harmonics or natural occurring frequencies that could occur when the two tones are sent. The frequencies may not vary more that +/- 1.5% from their nominal frequency, or the switching center will ignore the signal. The high frequencies may be the same volume or louder as the low frequencies when sent across the line. The loudness difference between the high and low frequencies can be as large as 3 decibels (dB) and is referred to as twist.
DTMF can be regarded as a simple form of orthogonal frequency division multiplexing[?].
Synonyms include multifrequency pulsing and multifrequency signaling.
wikipedia.org dumped 2003-03-17 with terodump